Harley Davidson O2 Sensor Location

Harley Davidson O2 Sensor Location - Web i recently had to replace the rear cylinder header pipe and the rear o2 sensor is located near the transmission and plugs in under the cover over the rear of the starter. Some dealerships are very keen to provide the stage 1 remap and others seem more reluctant due to some reported problems with persistent eml faults after remapping. Web check your exhaust system stem to stern. Vance&hines big radius, harley heavy breather, harley pro street tuner, and stage 2 torque kit. New 2019 street bob, about 3 months old. After that, i try to run diagnostic mode on the dash it show p00134, p00154, p00031 134 = front o2 sensor inactive 154 =.

Web you can go to your local stealership and mount your bungs in the same location as on the newer v's. Web replacing an o2 sensor to fix my check engine light! The '11 o2 sensors are located down low in the pipes ahead of the cat. Just type lsailor1 in the youtube search bar. Just a quick video on replacing my o2 sensor with the pipes still on!

I am an auto mechanic instructor at rtc in pittsburgh. The o2 bung for the rear cylinder is not in the factory location. See if the harness side of the o2 cables are capped off. If your not stacked (fuel pack with ecm download), something else may be be the problem (map sensor,, tps,, ecm reference voltage high,, etc) My specialty is with automotive computer systems.

Harley Davidson 4 Wire M12 12mm Lambda O2 Oxygen Sensor DELPHI 28488580

Harley Davidson 4 Wire M12 12mm Lambda O2 Oxygen Sensor DELPHI 28488580

O2 sensor bung location Harley Davidson Forums

O2 sensor bung location Harley Davidson Forums

O2 sensor bung location Harley Davidson Forums

O2 sensor bung location Harley Davidson Forums

For 20122017 HARLEY DAVIDSON 4 Wire O2 Oxygen Sensor VRod 32700006 eBay

For 20122017 HARLEY DAVIDSON 4 Wire O2 Oxygen Sensor VRod 32700006 eBay

Assistance with o2 sensors Harley Davidson VRod Forum

Assistance with o2 sensors Harley Davidson VRod Forum

Harley Davidson Touring Exhaust Review and Howto Hdforums

Harley Davidson Touring Exhaust Review and Howto Hdforums

removing O2 sensor on fxdb...help Harley Davidson Forums

removing O2 sensor on fxdb...help Harley Davidson Forums

O2 Sensor Unheated for 0717 HarleyDavidson 2771907 Precision Frameworx

O2 Sensor Unheated for 0717 HarleyDavidson 2771907 Precision Frameworx

O2 sensor connection help? Harley Davidson Forums

O2 sensor connection help? Harley Davidson Forums

How do I get at rear O2 sensor Connector Harley Davidson Forums

How do I get at rear O2 sensor Connector Harley Davidson Forums

Harley Davidson O2 Sensor Location - All the work was done by the dealer. If there is anything screwed into it with wires coming out of it after the exhaust manifold (the part that bolts to the cylinder head), that's your oxygen sensor. It should be part of the exhaust system, and it resembles a plug. Just a quick video on replacing my o2 sensor with the pipes still on! New 2019 street bob, about 3 months old. Web for you motorcycle guys new to my channel. Web this video shows how to install a new rear oxygen senor on a 2019 harley sport glide flsb. Just type lsailor1 in the youtube search bar. I was familiar with the earlier routing location to the plugs, it was easy. You may like my other videos.

Web o2 sensor and tune advice. My specialty is with automotive computer systems. Web this video shows how to install a new rear oxygen senor on a 2019 harley sport glide flsb. All the work was done by the dealer. I was familiar with the earlier routing location to the plugs, it was easy.

Web most harley dealers can now map out the rear o2 sensors when they do a “stage 1” remap with their diag 4 software. At 1500 miles had some upgrades done: I was familiar with the earlier routing location to the plugs, it was easy. Web has anyone with the new sensors pulled the wires to change pipes?

Web the bungs are tapered to align the sensor to the exhaust flow, and that requires that they be in a straight section of pipe and pointed in the direction of the bend if the straight section is shorter than a few inches. 2012 started with heated sensors, and they're moved farther away. All the work was done by the dealer.

Web the o2 sensors may still be deadheaded with resistors to fool the ecm to richen up the mixture. If there is anything screwed into it with wires coming out of it after the exhaust manifold (the part that bolts to the cylinder head), that's your oxygen sensor. Vance&hines big radius, harley heavy breather, harley pro street tuner, and stage 2 torque kit.

// 2017 Harley Davidson Road Glide Ultra.

Web i just bought a set of v&h power duals for my 2012 streetglide. The front cylinder bung is in the stock location just ahead of the x pipe. Web has anyone with the new sensors pulled the wires to change pipes? I was familiar with the earlier routing location to the plugs, it was easy.

Web Find The O2 Sensor That Needs To Be Removed.

The front o2 sensor is located near the front down tubes. Web replacing an o2 sensor to fix my check engine light! I followed the wires up along the frame then they disappear. Just type lsailor1 in the youtube search bar.

Web O2 Sensor And Tune Advice.

At 1500 miles had some upgrades done: The inspector (garage mechanic) entered f250 super duty and it came up with the o2 sensor and o2 sensor heater. Some dealerships are very keen to provide the stage 1 remap and others seem more reluctant due to some reported problems with persistent eml faults after remapping. The o2 bung for the rear cylinder is not in the factory location.

Web The O2 Sensors May Still Be Deadheaded With Resistors To Fool The Ecm To Richen Up The Mixture.

It needs more heat to make them work better. If your not stacked (fuel pack with ecm download), something else may be be the problem (map sensor,, tps,, ecm reference voltage high,, etc) Personally, i do not like the stock location and chose to make mine more hidden when i added them to my '07. See if the harness side of the o2 cables are capped off.