Ford Ranger 23 Coolant Temp Sensor Location
Ford Ranger 23 Coolant Temp Sensor Location - Web my engine coolant temp sensor (2.5l i4) is dead and bought a new one to replace it. I have a chiltons book and have been using fte and other sited for info but was unable to figure out where the coolant temperature sender was. I see that are two sensors that look similar to one another. Web we took the ranger as a classic example to demonstrate the functioning of the coolant temperature sensor. Temp sender, 12volt, usually 1 wire, can be 2, only used by dash board temp gauge. Disconnect the other to verify.
Web changing a coolant temperature sensor on a 2020 ford ranger plus a really helpful free tool! Web try installing a new thermostat. I can check alldata at work tomorrow but if someone knows that would be a big help. Turn the key to run (engine off). Is it the front one or back one that i need to replace?
Web there are 2 coolant temp sensors, one for the temp gauge, and one for the pcm. Only replace if you have a ect check engine code and the wiring is in good shape and the sensor is connected. Ect sensor, 5volt, 2 wire, only used by the engine computer. The one we are looking for is the one here on the driver's side. Web try installing a new thermostat.
The coolant sensor protrudes from the top of it near where it ends. Web changing a coolant temperature sensor on a 2020 ford ranger plus a really helpful free tool! As i said before, remove this plug, buy a sender, install. Is it the front one or back one that i need to replace? $8 well spent, since it regulates.
Ect sensor, 5volt, 2 wire, only used by the engine computer. Web the temp gauge will be dead if you got the right one. For any of owners of an older 4 cylinder ford ranger, perhaps this video will help you locate and replace your engine coolant temperature. Please let us know if you need anything else to get the.
It controls the fans and the temperature gauge. For any of owners of an older 4 cylinder ford ranger, perhaps this video will help you locate and replace your engine coolant temperature. So its behind & below the coil pack. I can check alldata at work tomorrow but if someone knows that would be a big help. The coolant sensor.
Turn the key to run (engine off). Only replace if you have a ect check engine code and the wiring is in good shape and the sensor is connected. You say there is a plug in this place. Is it the front one or back one that i need to replace? I have a chiltons book and have been using.
The one we are looking for is the one here on the driver's side. Images (click to make bigger) sponsored links. Please let us know if you need anything else to get the problem fixed. Web there are 2 coolant temp sensors, one for the temp gauge, and one for the pcm. So its behind & below the coil pack.
Turn the key to run (engine off). It controls the fans and the temperature gauge. Web my apologies to my clash subscribers. Disconnect one of the two, see if temp gage goes wonky. The cht on that engine is installed into the cylinder head on the right side.
The sensor for the gauge will have a single wire connector, the pcm temp sensor will have a 2 wire connector. The one we are looking for is the one here on the driver's side. This video is to explain which coolant temp sensor on a ford ranger with the 4.0l sohc engine is for the ecm and gauge. You.
For any of owners of an older 4 cylinder ford ranger, perhaps this video will help you locate and replace your engine coolant temperature. Web the one wire sensor is the one you need, it should be located right about where the upper radiator hose meets the intake manifold. Both should be close to the thermostat housing. Is it the.
They look similar but are not at all the same. Web needed to differentiate between the temp sensor for the gauge and the temp sensor for the computer. Web warm up the engine so the gage registers the temp. Web ford ranger 4.0 sohc coolant temp sensor location. This video is to explain which coolant temp sensor on a ford.
They look similar but are not at all the same. Disconnect one of the two, see if temp gage goes wonky. Web there are 2 coolant temp sensors, one for the temp gauge, and one for the pcm. Web i've been trying to locate a coolant leak which i have found but i am unsure which of the 2 in.
Ford Ranger 23 Coolant Temp Sensor Location - As i said before, remove this plug, buy a sender, install. Web needed to differentiate between the temp sensor for the gauge and the temp sensor for the computer. There's a small clip at the bottom. They look similar but are not at all the same. Web the temp gauge will be dead if you got the right one. Images (click to make bigger) sponsored links. Disconnect the other to verify. Is it the front one or back one that i need to replace? I see that are two sensors that look similar to one another. The coolant sensor protrudes from the top of it near where it ends.
For any of owners of an older 4 cylinder ford ranger, perhaps this video will help you locate and replace your engine coolant temperature. Temp sender, 12volt, usually 1 wire, can be 2, only used by dash board temp gauge. Images (click to make bigger) sponsored links. The coolant sensor protrudes from the top of it near where it ends. The dash sensor is easier to see from underneath.
Web my apologies to my clash subscribers. Most parts stores will send you away with an ect sensor, lol. Web try installing a new thermostat. Web the coolant temp sensor's located below the intake manifold, just behind the thermostat housing that we've just removed.
$8 well spent, since it regulates the temperature of the coolant that your new sensor is reporting. 10k views 2 years ago. Web ford ranger 4.0 sohc coolant temp sensor location.
Web fuel injected engines have 2 temp units. Most parts stores will send you away with an ect sensor, lol. You say there is a plug in this place.
The Dash Sensor Is Easier To See From Underneath.
Web i bought a 1999 ford ranger sport with a long bed, 2wd 2.5l a few weeks ago and have been doing the routine matinence that was not so routine for the po. I can check alldata at work tomorrow but if someone knows that would be a big help. This video is to explain which coolant temp sensor on a ford ranger with the 4.0l sohc engine is for the ecm and gauge. If you don't want to spend the $8, slap a piece of cardboard in front of the radiator for a short drive.
The Sensor For The Gauge Will Have A Single Wire Connector, The Pcm Temp Sensor Will Have A 2 Wire Connector.
Web the one wire sensor is the one you need, it should be located right about where the upper radiator hose meets the intake manifold. Web ford ranger 4.0 sohc coolant temp sensor location. Web changing a coolant temperature sensor on a 2020 ford ranger plus a really helpful free tool! As i said before, remove this plug, buy a sender, install.
So Its Behind & Below The Coil Pack.
I see that are two sensors that look similar to one another. Web i've been trying to locate a coolant leak which i have found but i am unsure which of the 2 in this photo is the coolant temp sensor. Web there are 2 coolant temp sensors, one for the temp gauge, and one for the pcm. $8 well spent, since it regulates the temperature of the coolant that your new sensor is reporting.
Web We Took The Ranger As A Classic Example To Demonstrate The Functioning Of The Coolant Temperature Sensor.
The one we are looking for is the one here on the driver's side. Web that big metal tube on the passenger side that goes past the coil,, follow it back behind the engine. Web warm up the engine so the gage registers the temp. Ect sensor, 5volt, 2 wire, only used by the engine computer.